Glossary entry (derived from question below)
English term or phrase:
compressor port
German translation:
Kompressoranschluss
Added to glossary by
Ruth Wiedekind
Oct 28, 2007 15:51
16 yrs ago
English term
compressor port
English to German
Tech/Engineering
Automotive / Cars & Trucks
Kontext (Klimaanlagenkompressor):
The roughness (o-ring surface finish) height shall not exceed 0.8 RA or 6.3 RT of the entire contact surface, per Figure 1. Local flaws (depressions) shall be allowed only if they are outside the specific sealing ring areas. No scuffs or burrs shall be allowed which would prevent total surface contact between the **compressor ports** sealing surfaces and the plumbing pipe connector.
Kann man einfach "Kompressoranschluss" schreiben? (-kanal/ -öffnung?) Und welches Teil ist eigentlich der "Stutzen": dieses oder der "plumbing pipe connector"?
The roughness (o-ring surface finish) height shall not exceed 0.8 RA or 6.3 RT of the entire contact surface, per Figure 1. Local flaws (depressions) shall be allowed only if they are outside the specific sealing ring areas. No scuffs or burrs shall be allowed which would prevent total surface contact between the **compressor ports** sealing surfaces and the plumbing pipe connector.
Kann man einfach "Kompressoranschluss" schreiben? (-kanal/ -öffnung?) Und welches Teil ist eigentlich der "Stutzen": dieses oder der "plumbing pipe connector"?
Proposed translations
(German)
3 | Kompressoranschluss | jccantrell |
4 | Drucköffnung | Vere Barzilai |
Change log
Oct 28, 2007 16:34: Steffen Walter changed "Field" from "Other" to "Tech/Engineering" , "Field (specific)" from "Engineering (general)" to "Automotive / Cars & Trucks" , "Field (write-in)" from "Automobil" to "(none)"
Proposed translations
23 hrs
Selected
Kompressoranschluss
This is how I know a 'port' from hydraulics and pneumatics. This site says:
"Über den Kompressoranschluss strömt Luft mit ca.
6 bar zur Messingdüse und erzeugt aufgrund der Ver-
engung einen Unterdruck von ca. 80 mbar. Dadurch
wird ein Volumen von 200 – 300 m angesaugt. Um
90 Grad versetzt zum Kompressoranschluss ist ein
Prüf- und Messstutzen ½ Zoll angebracht, welcher
nach der Messung mit einem Stopfen geschlossen
werden kann."
"Über den Kompressoranschluss strömt Luft mit ca.
6 bar zur Messingdüse und erzeugt aufgrund der Ver-
engung einen Unterdruck von ca. 80 mbar. Dadurch
wird ein Volumen von 200 – 300 m angesaugt. Um
90 Grad versetzt zum Kompressoranschluss ist ein
Prüf- und Messstutzen ½ Zoll angebracht, welcher
nach der Messung mit einem Stopfen geschlossen
werden kann."
3 KudoZ points awarded for this answer.
Comment: "Ich denke, das ist das einfachste."
14 hrs
Drucköffnung
www.moro.it/def/contenuti/Documenti/manuale_ita.pdf
"..... in Auto-Klimaanlagen und in stationären Klima-. und Kälteanlagen ..... Drucköffnung gesteuert wird. etc. "
es ist viel Text bis man darauf stösst, aber da es sich um Klimanlage handelt, spricht man von Drucköffnung.
"..... in Auto-Klimaanlagen und in stationären Klima-. und Kälteanlagen ..... Drucköffnung gesteuert wird. etc. "
es ist viel Text bis man darauf stösst, aber da es sich um Klimanlage handelt, spricht man von Drucköffnung.
Note from asker:
Dann gibt es doch auch noch die Saugöffnung, wenn ich mich nicht irre ... |
Something went wrong...